Skip to main content

Metal Stitching of Engine Block RA Power Solutions

 In the event of a fracture or damage to the casting, there is no need to replace the key components of the engine or the equipment installed in heavy engineering facilities.

Metal stitching and metal locking processes can be used to repair cracks and damaged components on-site, regardless of their application or profile.

Metal Stitching of Engine Block in Process

The following are the major characteristics of using metal locking to repair cracks and damaged castings in engine blocks and large cast components:

  • For the repair of cracks and broken components, RA Power Solutions utilizes a cold metal lock and stitching procedure.

  • Metal stitching and metal locking techniques can be used to replace a major amount of damaged components with new casting pieces.

  • Because no heat is created, metal stitching and metal locking is the most trusted approach for crack mending. Unlike welding, it is a cold procedure that results in no change in the form or profile of the component.

  • Metal stitching and metal locking can be used to repair cracks on the spot without disassembling the equipment.

  • The lock and stitch method of crack repair and broken casting repair is considerably less expensive than purchasing pricey and new parts.

Contact us at rajshahani@rapowersolutions.com to learn more about metal surgery, cast iron fracture repair metal stitching of engine block, metal stitching of crankcase, metal stitching engine block, metal locking service, metal stitching engine block repair, metal stitching company in India, metal stitching repairs, metal lock process, engine block repair by metal stitching, Metal locking a crack engine block, crack repair by metal stitching, Metal Stitching Engine Block, Cracked Engine Block Repair Stitching 

Mob No: +91 9582647131

Tel No: +91-124–4378292, 4251615

Email ID: info@rapowersolutions.com

Comments

Post a Comment

Popular posts from this blog

Crankpin machining is required in case of following

  Crankpin machining is required in case of the following damage to the crankpin. Development of excessive taper & ovality on a crankpin.  Seizure of crankpin bearing Development of bearing marks and pitting on crankpins. Due to above defects it is necessary to get the crankpin machining undertaken.  RA Power Solutions have more than 41 years of experience in undertaking machining of crankpin onsite up to 700mm. There is no requirement of removing the crankshaft from the engine block and transporting to the workshop. We have a team of experienced technicians who fly all over the world to undertake crankpin machining on site. For More Information Visit Our Sites: http://connectingrodrepair.com/, https://metalstitchinglocking.com/,  marineengine.in , http://turbineshaft.in/, http://rebabbittingbearing.com/, https://engineoverhaulingservices.com/
Post a Comment
Read more

Metal Stitching & Metal locking of Engine Block

  RA Power solutions have been  undert aking repair & maintenance of heavy equipment in industries, power plants, and diesel engines installed on the vessel for the last more than 4 decades.     We have experienced that in spite of following the rigid maintenance schedule mentioned in the maintenance manual of the  manufacturer serious  accidents do take place breaking the casing of the engine, compressor, Heavy engineering equipment into pieces or developing multiple cracks.       RA Power Solutions recommended repair of damaged cast iorn casting,  Aluminium  bronze components by metal lock/metal stitching process having following advantages:        i ) The main advantage of  repair of  damaged or cracked engine block   by  metal lock / metal stitching  process is that it is cold  method of repair  and no heat...
Post a Comment
Read more

Journal Bearing Manufacturer By RA Power Solutions

  Crank pin journal  of Wartsila 18V32 was reported to be damaged by one of our client in Southeast Coast of Africa. RA Power Solutions team of two technicians was deputed and following were the main observations: On visual inspection it was observed that  crank pin no. 2 and Crank pin nos 6 were severely scored with bearing line marks having approximate depth of 0.5 mm. The hardness was observed between 30 and 50 HRC at different spots. On undertaking the MPI of crankpin no. 2 and crankpin no. 6, only multiple surface cracks were observed The crankpins of the crankshaft were checked for taper and ovality and maximum ovality of 0.6 mm was observed. After the initial inspection of crankpin journal 2 and crankpin journal no. 6, the  crankshaft grinding  was done by latest design of onsite crankshaft grinding equipment. The crankshaft grinding equipment having the range of 260 to 300 mm was used. Following process for crank pin journal repair was adopted. Rough gri...
Post a Comment
Read more